# HAR 6-77-96 Repair of steel pipe **Citation:** HAR 6-77-96 **Type / status:** regulation / current **Agency:** Hawaii Public Utilities Commission **Effective:** 1994-09-03 **Published:** 1994-04-15 serviceability of a length of steel pipe must be repaired or removed. If a repair is made by grinding, the remaining wall thickness must at least be equal to either: (1) The minimum thickness required by the tolerances in the specification to which the pipe was manufactured; or (2) The nominal wall ## Document text serviceability of a length of steel pipe must be repaired or removed. If a repair is made by grinding, the remaining wall thickness must at least be equal to either: (1) The minimum thickness required by the tolerances in the specification to which the pipe was manufactured; or (2) The nominal wall thickness required for the design pressure of the pipeline. (b) Each of the following dents must be removed from steel pipe to be operated at a pressure that produces a hoop stress of twenty percent, or more, of SMYS: (1) A dent that contains a stress concentrator such as a scratch, gouge, groove, or arc burn; (2) A dent that affects the longitudinal weld or a circumferential weld; and (3) In pipe to be operated at a pressure that produces a hoop stress of forty percent or more of SMYS, a dent that has a depth of: (A) More than one-quarter inch in pipe 12-3/4 inches or less in outer diameter; or (B) More than two percent of the nominal pipe diameter in pipe over 12-3/4 inches in outer diameter. For the purpose of this subsection a "dent" is a depression that produces a gross disturbance in the curvature of the pipe wall without reducing the pipe-wall thickness. The depth of a dent is measured as the gap between the lowest point of the dent and a prolongation of the original contour of the pipe. (c) Each arc burn on steel pipe to be operated at a pressure that produces a hoop stress of forty percent, or more, of SMYS must be repaired or removed. If a repair is made by grinding, the arc burn must be completely removed and the remaining wall thickness must be at least equal to either: (1) The minimum wall thickness required by the tolerances in the specification to which the pipe was manufactured; or (2) The nominal wall thickness required for the design pressure of the pipeline. (d) A gouge, groove, arc burn, or dent may not be repaired by insert patching or by pounding out. (e) Each gouge, groove, arc burn, or dent that is removed from a length of pipe must be removed by cutting out the damaged portion as a cylinder. [Eff ] (Auth: HRS '269-6) (Imp: 49 C.F.R. '192.309, October 1, 1990) ## Provenance - Official: Yes - Source: - Source ID: `hi-puc-har-6-77` - SHA-256: `5b5405f44c8429dd020c0d79b9f9acf8b065c55342b8285f4a3b3d0cdbd80317` - Retrieved: 2026-08-12T08:22:24.168Z - Exported: 2026-08-25T08:46:43.559Z - Document slug: `hi-har-har-6-77-96` ### Source metadata ```json { "jurisdiction": "US-HI", "chapter": "HAR Chapter 6-77", "provisionKind": "section", "adoptedOn": "1994-04-15", "filedOn": "1994-08-24", "exactEffectiveDateAvailableInPublication": true, "publicationStatus": "officially-published-superseded-slated-for-repeal", "phmsaProgramParticipant": false, "stateCertificationRepresented": false, "federalInspectionAndEnforcement": [ "interstate gas", "intrastate gas", "interstate hazardous liquid", "intrastate hazardous liquid" ], "fixedFederalBaseline": "1990-10-01", "editorialModernizationApplied": false, "references": [ { "citation": "49 CFR 192.309", "referenceType": "federal_regulation", "url": "https://www.ecfr.gov/current/title-49/section-192.309", "incorporatedEdition": "1990-10-01" }, { "citation": "HRS 269-6", "referenceType": "state_statute", "url": "https://data.capitol.hawaii.gov/hrscurrent/Vol05_Ch0261-0319/HRS0269/HRS_0269-0006.htm" } ], "caveats": { "exactScope": "Complete substantive text of the Hawaii Public Utilities Commission publication of HAR Chapter 6-77: 196 non-reserved numbered sections and Appendices A through D. Four expressly reserved section slots are inventory-only. The PUC's April 2026 page links a 160-page signed scan; an official 178-page text-layer copy from Budget and Finance is used as the higher-quality transcription aid. The publication is an April 15, 1994 adoption, filed August 24 and effective September 3, 1994, based on the October 1, 1990 federal text; it is not a current restatement of federal pipeline standards.", "applicability": "Hawaii is not represented as certified, as an agreement state, or as an interstate agent under the PHMSA federal-state pipeline safety program. PHMSA states that its Office of Pipeline Safety inspects and enforces federal pipeline safety regulations for interstate and intrastate gas and hazardous-liquid pipelines in Hawaii. Chapter 6-77 may remain relevant as published state utility material, but it must not be used to infer current Hawaii inspection or enforcement authority.", "currentness": "The Hawaii PUC still links Chapter 6-77 on its official rules page, updated April 2026. Hawaii's official 2022 periodic rules-review report separately says Chapter 6-77 is to be repealed, was superseded by statute and a federal takeover letter, and cites 2009 Act 25. Because the PUC page does not mark the chapter repealed, this connector preserves the published text with an explicit superseded/slated-for-repeal warning rather than declaring an unproved completed administrative repeal.", "incorporation": "The chapter repeatedly identifies the October 1, 1990 edition of 49 CFR Parts 191 and 192 and its appendices as the implemented source. That fixed, obsolete baseline is preserved exactly. Current federal text, later amendments, and current editions of incorporated private standards must not be silently substituted when researching what this publication says.", "excludedScope": "This connector excludes HAR Chapter 6-83 one-call damage prevention, utility rates and service standards, statutes as standalone documents, dockets, orders, tariffs, federal text, current federal amendments, and the full text of incorporated private standards. Those materials require separate completeness, currentness, applicability, and rights analysis.", "rights": "Official Hawaii and PHMSA artifacts are retained with attribution and SHA-256 provenance. Public access does not establish unrestricted rights in site presentation, state marks, forms, or incorporated private standards. The connector records citations to private standards but makes no independent rights claim for those works." }, "region": "HI" } ```