# PPL Susquehanna, LLC — Hazardous Materials Safety Interpretation

- **operation:** document
- **citation:** 04-0222
- **title:** PPL Susquehanna, LLC — Hazardous Materials Safety Interpretation
- **source type:** guidance
- **agency:** Pipeline and Hazardous Materials Safety Administration
- **status:** guidance
- **official:** true
- **published on:** 2004-10-15
- **effective on:** Not available
- **summary:** 04-0222 response to PPL Susquehanna, LLC concerning 173.428.
- **machine formats:** - **json:** https://regulus.evalyn.ai/document/phmsa-interpretation-04-0222.json
- **markdown:** https://regulus.evalyn.ai/document/phmsa-interpretation-04-0222.md
- **app url:** https://regulus.evalyn.ai/document/phmsa-interpretation-04-0222
- **source url:** https://www.phmsa.dot.gov/sites/phmsa.dot.gov/files/legacy/interpretations/Interpretation%20Files/2004/040222.pdf
**body:**

<<<PAGE 1>>>

U.S. Department
of Transportation
400 Seventh St., S.W.
Washington, D.C. 20590
Special Programs
Research and
OCT 15 2004
Administration
Mr. Michael Micca
Ref. No.: 04-0222
769 Salem Blvd.
PPL Susquehanna, LLC
Berwick, PA 18655
Dear Mr. Micca:
This is in response to your September 23, 2004 letter requesting clarification regarding the
marking requirements for empty Class 7 radioactive materials packaging under the
Hazardous Materials Regulations (HMR; 49 CFR Parts 171-180). In your scenario, you
describe your packaging as one that meets the "empty" requirements for radioactive materials
as specified in § 173.428. This section was modified under Docket HM-230 (69 FR 3632;
January 26, 2004), effective October 1, 2004. Specifically, you ask if you need to remove,
cover, or obliterate both the hazard communication markings (Part 172, Subpart E) and the
specification package marking ("USA DOT 7A Type A") on your package to remain in
compliance with § 173.428.
Based on the information provided, if the package is prepared in accordance with § 173.428
(that is, it meets the packaging, definition, and EMPTY labeling requirements specified in
that section), then all other hazard communication markings required by the HMR for this
material should be removed or covered during transportation. However, § 173.428 requires
the identification number for the material to remain on the packaging as specified under
§ 173.422(a). In addition, the specification marking "USA DOT 7A Type A," as required
under § 178.350(b) should remain on the packaging, unless, for some reason, the packaging
no longer conforms to the Part 178 specification requirements.
I hope this information is helpful. Please contact us if you require additional assistance.
Sincerely.
Hotte mither
Hattie Mitchell
Office of Hazardous Materials Standards
Chief, Regulatory Review and Reinvention
040222
173.428

<<<PAGE 2>>>

INFOCNTR
From:
To:
Sent:
Thursday, September 23, 2004 2:56 PM
mcmicca@pplweb.com
Satterthwaite
Subject:
Information Center Comments/Questions
INFOCNTR <RSPA>
$173.428
Empty Package
Below is the result of your feedback form.
It was submitted by
04-0222
Michael C. Micca (mcmicca@pplweb.com) on Thursday, September 23, 2004 at 14:55:52.
Email:
mcmicca@pplweb.com
Name: Michael C. Micca
Communications
Category:
Hazardous Materials Table, Special Provisions,
Hazardous Materials
Organization: PPL Susquehanna, LLC
Street: 769 Salem Boulevard
City: Berwick
State: Pennsylvania
Zip Code:
18655
Phone:
(570) 542-1790
Fax:
(570) 542-1857
marking requirements for a container that was previously used, and therefore, marked, as
Comments: I am looking for a formal response
(letter of interpretation) concerning the
2004. 49CFR173.422 and 49CFR173.428 require an
TYPE A packaging. The question pertains to the regulations in effect as of October 1,
EMPTY label and marked with the
four digit UN ID number (UN2908).
empty packaging to be labeled with the
specifically state that any labels previously applied must be removed,
These regulations
The regulations do not mention removing, obliterating, or
For a package that was previously shipped as a TYPE A package and will be
covering any markings
shipped as an EMPTY package in accordance with 49CFR173, what markings, if any, must be
- **truncated:** false
- **body characters:** 3288
