# gh Package & Product Testing — Hazardous Materials Safety Interpretation - **operation:** document - **citation:** 05-0204 - **title:** gh Package & Product Testing — Hazardous Materials Safety Interpretation - **source type:** guidance - **agency:** Pipeline and Hazardous Materials Safety Administration - **status:** guidance - **official:** true - **published on:** 2006-08-24 - **effective on:** Not available - **summary:** 05-0204 response to gh Package & Product Testing concerning 178.606. - **machine formats:** - **json:** https://regulus.evalyn.ai/document/phmsa-interpretation-05-0204.json - **markdown:** https://regulus.evalyn.ai/document/phmsa-interpretation-05-0204.md - **app url:** https://regulus.evalyn.ai/document/phmsa-interpretation-05-0204 - **source url:** https://www.phmsa.dot.gov/sites/phmsa.dot.gov/files/legacy/interpretations/Interpretation%20Files/2005/050204.pdf **body:** <<>> Washington, D.C. 20590 400 Seventh Street, S.W. Pipeline and Hazardous Materials Safety Administration AUG 24 2006 President and Technical Director Mr. H. Perry Hock Ref. No.: 05-0204 gh Package & Product Testing 4090 Thunderbird Lane Consulting, Inc. Fairfield, OH 45014 Dear Mr. Hock: This responds to your letter requesting clarification of the Hazardous Materials legulations (HMR; 49 CFR Parts 171-180) pertaining to the stack test prescribed i test, and how a guided load stack test should be set up and performed. You enclosed 178.606. Specifically, you asked when is it permissible to use a "guided load" stac illustrations and photographs of the tests. You provided a scenario as follows: dead load on each individual packaging or container, the packaging may fail. Frequently, When the gh Testing laboratory performs an "unguided" stack test, using steel plates as the failure results in one side of the specimen collapsing and not being able to keep the weight centered above it; however, the packaging remains intact without rupture or loss still intact and no loss of contents has occurred. You asked the following questions: of contents. Several of your clients assert that this is not a failure since the packaging is Q1. Is my client correct that this is not a failure of the stack test since the packaging is still intact and no loss of contents has occurred? In a guided load stack test, a load is directed vertically onto the test sample and applica. The aparasifin in your ofustrions may be use do cohave to be stacking test prescribed in $ 178.606, provided a constant load is applied for the НІНИННІ 050204 178.606 <<>> 24-hour duration of the test. If this equipment is used, a stack stability assessment must be made for one hour at the conclusion of the test. The stacking test is conducted to ensure that the inner receptacles or inner packagings do not leak any of the contents. The stability test ensures that the stacked packages are stable during transportation. There must be no leakage of the filling substance from the inner receptacle or inner packaging. No test sample any distortion likely to reduce its strength, cause instability in stacks of packages, may show any deterioration which could adversely affect transportation safety or or cause damage to inner packagings likely to reduce safety in transportation. Thus, the scenario you describe constitutes a failure of the packaging to pass the prescribed test. Q2. When a gh Testing laboratory places three of the same, unmodified "packs" into test that follows, are the packs considered to have passed the test? the guided load stack test fixtures, and they pass the test, as well as the stability A2. The answer is yes. Q3. Are the two tests supposed to give the same results? A3. It's our expectation that the two stack tests (guided or unguided load) give the same or similar results. I hope this satisfies your inquiry. If we can be of further assistance, please contact us. Sincerely, 7 John A. Gale Chief, Standards Development Office of Hazardous Materials Standards <<>> gh Package & Product airfield, OH 45014 090 Thunderbird Lane Phone (513) 870-0080 Fax (513) 870-0017 Testing and Consulting, Inc. 335 W. Melinda Lane Phoenix. AZ 85027 Phone (623) 869-8008 Fax (623) 869-8003 August 1, 2005 Engruno To: Mr. Edward T. Mazzullo Director, Office of Hazardous Materials Standards 6178.606 4007' Street S.W. U.S. DOT/RSPA (DHM-10) lesting Washington, DC 20590-0001 05-0204 From: Mr. H. Perry Hock President and Technical Director gh Package & Product Testing and Company 4090 Thunderbird Lane Fairfield, OH 45014 Subject: Performance testing of non-bulk packagings pursuant to CFR 49, §178.606 Dear Mr. Mazzullo, $178.606. Specifically when it is permissible to use a guided load stack test, and how a I am in need of a clarification on the regulations pertaining to the stack test as detailed in guided load stack test should be set up and performed. This question has been arising more often, as companies try to reduce cost by minimizing packaging remains intact without rupture or loss of contents. Once this happens, the weight falls. A debate has begun over the regulations and their intentions. An interpretation most often given to gh Testing, from several of our clients, claims that this is not a failure since the packaging is still intact and no loss of contents has occurred. Is our client correct with their interpretation of the regulations since the pack did not rupture or lose contents? The debate is that the stack test is to ensure the pack does not rupture under the load - not that it is a stability test. The debate then continues that the stability portion of the testing is ensured via the hour long stability test following the stack portion of the test. When gh Testing places three of the same, unmodified, packs into the guided load stack test fixtures, they pass the test, as well as the stability test that follows. Are the pack considered to pass the test? What if the pack was never tested using the unguided method results? and only resulted in the passing of the test? Are the two tests supposed to give the same <<>> I have seen illustrations and pictures from other institutions on how they perform a guided load stack test. I would like to know which is permissible pursuant to the regulations. load fixture, each with the required weight above it. Following this test, the stability is The first illustration is where all three required packs are placed into the sarne guided assessed pursuant to the regulations. Each stack 600 lbs. (1800 Ibs. total) any load and is not meant to be stacked on as a single unit. A good example might be a 5 I can understand performing the testing in this manor if the pack by itself car not balance gallon bottle with a tapered neck. The second illustration is one where an additional pack is "tested", using the guided load method as above. This is done since three packs cannot fit into or under the guided load fixture. Again, the stability would be assessed following the required stack test period. - so seat on calculation (2400 Ibs. total) -Extra Pack <<>> The third illustration is one where each pack is tested individually in a guided load stack test fixture. Again, the stability would be assessed following the required stack test period. - Each stack 600 Ibs. TUTT TOT And the fourth illustration is an unguided load stack test. - Each stack 600 Ibs. <<>> Below are photos of actual testing conducted at gh Testing. Results of unguided load test - pack was unable to maintain the load of 583 Ibs. and the pack collapsed. Guided Load Stack - with 17 additional pounds per pack for a total of 600 Ibs. per stack: Start of the test - the packs are supporting the entire weight, and the load spreader (plywood) is not touching any of the safety guides. <<>> After 24 hours, the load has shifted to the back side of the packagings, and the load spreader is now touching both the far and near guides. Single pack, 104°, after 28 days Combination pack, after 24 hours Note the "uniform crush". We typically see the same results whether a single pack is used in a guided load, or all three are placed in a straight line across, such as the photo typically see same results as above. The packs tend to perform better in the triangular above. The exception is when the packs are staggered in a triangular pattern, we do not stack test pattern since the weight shift seen above is very unlikely to occur in a staggered stack. <<>> Stability test on the above packs (only photos of two stacks of the single unit and one stack of the combination pack are included, but all six stacks passed): Stability tests after one hour If you have any further questions, please do not hesitate to call me at 513.870.0080 x 103. I look forward to your prompt response. Yours Truly, President and Technical Director H. Perry Hock gh Package & Product Testing and Consulting, Inc. - **truncated:** false - **body characters:** 8019