{"operation":"document","citation":"18-0050","title":"Mondi Group — Hazardous Materials Safety Interpretation","source_type":"guidance","agency":"Pipeline and Hazardous Materials Safety Administration","status":"guidance","official":true,"published_on":"2018-09-13","effective_on":null,"summary":"18-0050 response to Mondi Group concerning 178.521.","machine_formats":{"json":"https://regulus.evalyn.ai/document/phmsa-interpretation-18-0050.json","markdown":"https://regulus.evalyn.ai/document/phmsa-interpretation-18-0050.md"},"app_url":"https://regulus.evalyn.ai/document/phmsa-interpretation-18-0050","source_url":"https://www.phmsa.dot.gov/sites/phmsa.dot.gov/files/docs/standards-rulemaking/hazmat/interpretations/68461/180050.pdf","body":"<<<PAGE 1>>>\n\nSEP 1 3 2018\nU.S. Department\nof Transportation\nPipeline and Hazardous\nMaterials Safety\nAdministration\n1200 New Jersey Avenue, SE\nWashington, DC 20590\nMike Iannelli\nTechnical Manager\nMondi Group\n1310 Saybrook Crossing\nThompsons Station, 1N 3 7179\nReference No. 18-0050\nDear Mr. Iannelli:\nThis letter is in response to your March 28, 2018, email and subsequent phone conversations\nrequesting clarification of the Hazardous Materials Regulations (HMR; 49 CFR Parts 171-180)\napplicable to the location of the water-resistant ply in a 5M2 paper bag design. Specifically, you\nprovide the following example and ask whether it is in compliance with § 178.521 (b )(2):\n1. Next to product: 2-millimeter low density polyethylene\n2. Kraft Paper\n3. Kraft Paper coated with polyethylene\n4. Kraft Paper\nThe design standards for a 5M2 bag require at least three plies made of \"a suitable kraft paper, or\nof an equivalent paper\" in accordance with § 178.521 (b )(1 ). Section 178.521 (b )(2) states that a\n5M2 bag of three plies must be made waterproof by the use of a water-resistant ply as the ·\noutermost ply. However, a bag of four plies or more must be made waterproof by the use of\neither a water-resistant ply as one of the two outermost plies or a water-resistant barrier made of\na suitable protective material between the two outermost plies. The HMR do not define \"plies.\"\nA 5M2 paper bag may include plies made out of other materials provided there are at least three\nplies made out of a material equivalent to a suitable Kraft Paper. Therefore, the bag described in\nyour letter is a four-ply bag. It is the opinion of this Office that if the polyethylene coated ply-\nwhich you described as one of the two outermost plies-is water-resistant, your bag construction\nmeets the design standards in § 178.521 (b )(2).\nI hope this information is helpful. Please contact us if we can be of further assistance.\nSincerely,\n~psY'~~\nT. Glenn Foster\nChief, Regulatory Review and Reinvention Branch\nStandards and Rulemaking Division\n\n<<<PAGE 2>>>\n\nJanuary, Ikeya CTR (PHMSA)\nFrom: INFOCNTR (PHMSA)\nSent:\nTo:\nThursday, March 29, 2018 1:21 PM\nHazmat Interps\nSubject: FW: Request for Clarification\nlkeya and Alice,\nBelow in a request for a letter of interpretation. Mr. Lannelli spoke with Eugenio. Let me know if you have any questions.\nThanks,\nJodi\nFrom: Iannelli Mike (US, Atlanta) [mailto:MIKE.IANNELLl@mondigroup.com]\nSent: Wednesday, March 28, 2018 6:30 PM\nTo: INFOCNTR (PHMSA) <INFOCNTR.INFOCNTR@dot.gov>\nSubject: Request for Clarification\nI would like to request a formal notification that the following construction does not meet the requirements of title 49\nCFR\n178.521 Standards for Paper Bags.\nWe have been informed by our customer, operating in Europe, that the following construction is acceptable in Europe as\na 5M2 construction. Based on our interpretation of the 178.521 along with the published interpretations, we do not\nbelieve this construction is in compliance with 49 CFR 178.521 and Mondi Bags USA is currently unwilling to certify a\npackage with this construction.\nPlease confirm that we are correctly interpreting the following construction as not in compliance.\nPly 1 (next to product) 2 mil Low De'nsity Polyethylene\nPly 2 Kraft Paper\nPly 3 Kraft Paper coated with polyethylene\nPly 4 (outer ply)\nKraft Paper\nBest Regards,\nMike\nMike Iannelli\nTechnical Manager\nIndustrial Bags\nMondi\n131 O Saybrook Crossing\nThompsons Station, TN 37179\nTel: 503-360-7078\nMobile: 503-360-7078\nEmail: mike.iannelli@mondigroup.com\nwww.mondigroup.com\n1\n\n<<<PAGE 3>>>\n\nLehman, Victoria (PHMSA)\nFrom:\nSent:\nTo:\nSubject:\nIannelli Mike (US, Atlanta) <MIKE.IANNELLI@mondigroup.com>\nWednesday, April 11, 2018 5:06 PM\nLehman, Victoria (PHMSA)\nRE: 5M2 letters of interpretation\nGood afternoon Ms. Lehman,\nIt was a pleasure to discuss this topic yesterday, and thank you for being responsive to my question.\nThank you for sending the copies of the interpretations, as this matches the ones I have on file. I have enclosed in red\nand in brackets additional comments/ questions below regarding the section cited.\nThe letter that causes the most confusion in my mind is the 00-0191 response letter which appears to be not unclear\nverses other letters. The 95-0309 letter appears to be very clear in confirming the bag referenced as a 4 ply bag. Since\nthe 1990's, the industry has used the 95-0309 letter as the basis for counting plys and intern determining where the\nwater resistant ply should be located to comply with §178.521. Based on the 95-0309, the industry has counted paper\nplys in order to determine if a bag is 3 ply or 4 ply and not considered film to be a ply counted. If film is now counted as\nan equivalent paper ply, this could signal a large change in how bags are constructed in the industry.\nWith respect to my original question sent on 3/28/18, I believe the construction to not be in compliance based on this\nbeing considered a three ply bag and the position of the water resistant ply not being the outer ply.\nPlease contact me with additional questions concerning my original questions or comments.\nSincerely,\nMike\nMike Iannelli\nTechnical Manager\nIndustrial Bags\nMondi\nTel: 503-360-7078\nMobile: 503-360-7078\nFrom: Lehman, Victoria (PHMSA) [mailto:victoria.lehman@dot.gov]\nSent: Tuesday; April 10, 2018 4:30 PM\nTo: Iannelli Mike (US, Atlanta)\nSubject: SM2 letters of interpretation\nGood afternoon Mr. Iannelli,\nThanks for taking time to discuss SM2 bag letter on your commute. Attached are the previous interpretations\nPHMSA/RSPA have issued. The following list includes excerpts:\n~1 ' ';& '.f, '¼'S'.t ; ··\nc,·i ,;uJJ:~ !\n~,.-~ :c, .. 3} ,,_s.l;:~,;>,-] ,\nQ1. Does the statement in§ 178.521(b}(2} in reference to the number of plies only mean paper plies, or does it\nalso include plastic film plies which may be used in combination with paper plies?\n1\n\n<<<PAGE 4>>>\n\nAl. The \"UN5M2\" multi-wall bag must be made of suitable kraft paper or an equivalent paper with at least three\nplies. To prevent the entry of moisture, a plastic film ply may be used as a waterproof ply or water-resistant\nbarrier in combination with paper plies as prescribed§ 178.521(b)(2). [Kraft paper refers to a specific grade of\npaper typically used in a multiwall bag. The statement \"or an equivalent paper\", I believe this is in reference to\nother paper grades such as liner board grade. However, does the answer in Al suggest that a \"film\" ply could be\na substitute to a paper ply if used as a waterproof ply? ]\nQ2. Is the plastic film ply considered a separate ply if it is laminated or bonded in some way to a paper ply, or is\nit only considered a separate ply if it is free and not bonded to a paper ply?\nA2. A plastic film ply bonded or larninated to the inner surface of a three ply bag as a waterproof ply or barrier\nwould be considered a separate ply. [This answer appears to agree with the June 30, 1995 response to Mr.\nJimmy Druey, in which Edward Mazzulo responded that \"The bag described is a four ply bag\". In Mr. Druey's\nquestion, the construction had 3 mil linear low density plastic film ply laminated to the third paper ply. Mr.\nMazzulo refers to the combination of the 3 mil film ply laminated to paper collectively as the third ply. This\nwould appear to support that a film/paper lamination is \"one ply\" and not \"two plys\".]\nQ3. Is a bag constructed of a plastic film inner ply laminated to a ply of kraft paper having an outer ply of water-\nresistant kraft paper considered a three ply \"UN5M2\" bag.\nA3. Yes, provided the bag complies with all other requirements of§ 178.521 and meets the testing\nrequirements of Subpart M of Part 178. [The question (Q3) is not listed verbatim as asked by Mr. Ruebush who\nasks if a third ply of paper necessary at the end of his original question. The response by Mr. Billings appears to\nauthorize a bag with two paper plys and a film ply to be acceptable based on the altered phrasing of the original\nquestion. Mr. Billings does state that it must also meet requirements of§ 178.521 so it is unclear if he is\nreferring to the need for an additional paper ply as asked by Mr. Ruebush. If the response supports only two\npaper plys, this appears to be opposed to the wording in §178.521(1) Standards for Paper Bags, which states\nthat \"Bags must be made of a suitable kraft paper, or of an equivalent paper with at least three plies.\"\n95-0309\n13-0197\nThis is in response to your June 15, 1995 fax to Ms. Susan Murphy, asking whether your bag construction\ncomplies with the standards for a UN 5M2 paper bag. The bag you described is a four ply bag. The two\ninnermost plies are kraft paper. The third ply is 3 mil linear low density plastic laminated to paper. The plastic\nside of the third ply faces inward, toward the product. The outermost ply is kraft paper.\nIt is our, opinion that the bag you described meets the requirement in 49 CFR 178.521(b)(2) that \"a bag of four\nplies or more must be made waterproof by the use of either a waterresistant ply as one of the two outermost\nplies or a waterresistant barrier made of a suitable protective material between the two outermost plies.\"\nProvided the bag complies with all other requirements of 49 CFR 178.521, and meets the testing requirements\nof Subpart M of Part 178, the bag may be marked as a UN 5M2 paper bag. [In the first paragraph of the response\nby Mr. Mazzullo, he states clearly and in no uncertain terms that \"The bag you described is a four ply bag.\" This\nis consistent with the interpretation used for years in the industry.]\nIn your email you describe the bag as three-plied, with a paper ply innermost layer coated with a water-\nresistant polymer facing inward (towards the product), a middle paper ply layer, and an outermost layer of\npaper ply having a water-resistant polymer coating facing inward ... The requirements for DOT specification 5M2\npaper bags in § 178.521 do not specify the orientation (i.e. inward or outward facing) of the water-resistant\ncoating on the outermost. [I do not have questions regarding this letter.]\n02-0030\nIt is the opinion of this Office that for purposes of§ 178.521, UN 5M2 bag, the term \"water resistant\" means\n\"waterproof\". Wet strength paper which does not resist the penetration of water is not suitable for use as a\nwater resistant barrier. [No issues]\n95-0311\n2\n\n<<<PAGE 5>>>\n\nThe exemption to which you refer, addressing a stitched top closure, is not inconsistent with SM2 standards; it\npermits a departure only from 5M2 requirement for waterproof seams and closures.\nPlease let me know if you have additional questions or information for us.\nRespectfully,\nVictoria Lehman\nTransportation Specialist- Regulatory Review & Reinvention (PHH- 12)\nU.S. Department of Transportation (U.S. DOT)\nPipeline and Hazardous Materials Safety Administration (PHMSA)\nOffice of Hazardous Materials Safety (OHMS)\nEast Building, 2nd Floor (E24-408)\n1200 New Jersey Ave., SE\nWashington, D.C. 20590\n(202) 366-91281 victoria.lehman@dot.gov I http://phmsa.dot.gov/hazmat I Follow PHMSA on Twitter\nThis e-mail as well as any files transmitted with it is confidential and may well contain information which is\nlegally privileged. It is intended solely for the use of the individual or the entity to whom it is addressed. If you\nare not the intended recipient of this e-mail, you are hereby on notice of this status. Any disclosure, copying,\ndistribution, dissemination or publication of the information contained therein is strictly prohibited, unless you\nhave been permitted thereto by the sender, and might be a breach of confidence. If you are not the intended\nrecipient, please return this e-mail immediately to the sender and then delete this message from your system.\nThe sender is not liable for the proper transmission of this information nor for any delay in its receipt.\n3\n\n<<<PAGE 6>>>\n\n...\n\"\n. o\nU.S. Department\nof Transportation\nResearch and\nSpecial Programs .\nAdministration\n400 Seventh St., S.W.\nWashington, D.C. 20590\nJAN - 2 2001\nMr. Richard Ruebush\nInternational Paper\nP .0. Box 4687\nSpartanburg, SC 29304-5687\nRef. No. 00-0191\nDear Mr. Ruebush:\nThis is in response to your letter dated July 10, 2000, regarding construction of \"UNSM2\" paper bags\nof three plies and four plies authorized in§ 178.52l(b)(2) of the Hazardous Materials Regulations\n(HMR; 49 CFR Parts 171-180). You state the multi-wall bags are sometimes constructed either with\nplastic film plies · or plastic film plies laminated to paper plies with adhesives, either with all over adhesive\ncoverage or stripes of adhesive.\nYour questions are paraphrased and answered as follows:\nQ 1. Does the statement in § 178.521 (b )(2) in reference to the number of plies only mean paper\nplies, or does it also include plastic film plies which may be used in combination with paper\nplies?\nAl. The\" UNSM2\" multi-wall bag must be made of suitable kraft paper or an equivalent paper with\nat least three plies. To prevent the entry of moisture, a plastic film ply may be used as a\nwaterproof ply or water-resistant barrier in combination with paper plies as prescribed\n§ 178.52l(b)(2).\nQ2. Is the plastic film ply considered a separate ply if it is laminated or bonded in some way to a\npaper ply, or is it only considered a separate ply ifit is free and not bonded to a paper ply.\nA2. A plastic film ply bonded or laminated to the inner surface of a three ply bag as a waterproof\nply or barrier would be considered a separate ply.\n\n<<<PAGE 7>>>\n\n' ,\nQ3. Is a pag constructed of a plastic film inner ply laminated to a ply of kraft paper having an outer\nply of water-resistant kraft paper considered a three ply \"UNSM211 bag.\nA3. Yes, provided the bag complies with all other requirements of§ 178.521 and meets the testing\nrequirements of Subpart M of Part 178.\nI hope this satisfies your inquiry. If we can be of further assistance, please contact us.\nSincerely, nt/d+\nDelmer F. Billings\nChief, Standards Development\nOffice of Haz.ardous Materials Standards\n\n<<<PAGE 8>>>\n\n-\nI • ,,,,\n, ,\n, ~\n.\n/j\n,,\n.\n'\nINTERNATIONAL@ PAPER\nCUSTOMER RESOURCE CENTER\n8vt5vu.JV]\n~ /;'(. s-~,\nP.o . BOxs687 Oo- o Ja (\nSPARTANBURG, SC 29304-5687 I\nPHONE: 864-596-7140\nFAX:864-596-7175\nJuly 10, 2000\nU.S. Department of Transportation\nResearch and Special Programs Administration\n400 Seventh Street, S.W.\nWashington, D.C. 20590-0001\nOffice of Hazardous Materials Standards DHM-10:\nI have some questions about 5M2 paper bags as mentioned in 49 CFR 178.52l(b)(2). My questions are in\nreference to the statements about bags of three plies and bags of four plies or more.\nMultiwall bags are sometimes constructed either with plastic film plies between paper plies or plastic film\nplies laminated to paper plies with adhesives, either with all over adhesive coverage or stripes of adhesive.\n1. Does the statement about the number of plies only mean paper plies or does it also include plastic :film\nplies which may be in combipation with the paper plies?\n2. Is the plastic film ply conside,red a separate ply if it is laminated or bonded in some way to a paper ply\nor is it only considered a separate ply if it is free and not bonded to a paper ply?\n3. Is a bag construction such as a plastic :film inner ply laminated to a ply of kraft paper having an outer\nply of water resistant kraft paper considered a three ply 5M2 bag or is it necessary to have a third ply\nof paper?\nI would be grateful if you can provide some clarification on these issues for me. Please contact me if you\nneed more information at 864-596-7159 or at the address on the letterhead\nRegards,\n~~\nRichard Ruebush\nDOT Packaging Coordinator\n\\","truncated":false,"body_characters":15572}