Leschaco, Inc. — Hazardous Materials Safety Interpretation

Page 1U.S. Department of Transportation Pipeline and Hazardous Materials Safety Administration 1200 New Jersey Avenue, SE Washington, DC 20590 November 14, 2023 Mr. Hien Le Manager – Hazmat and Compliance Leschaco, Inc. 15355 Vantage Parkway West, Suite 240 Houston, TX 77032 Reference No. 23-0008 Dear Mr. Le: This letter is in response to your January 30, 2023, email concerning the use of a technical name as part of a proper shipping name under the Hazardous Materials Regulations (HMR; 49 CFR Parts 171-180). Specifically, your email pertains to the shipment of dimethyl phthalate as “UN3082, Environmentally hazardous substance, liquid, n.o.s., 9, III.” In your email, you note that the safety data sheet (SDS) for this material states the technical name is “dimethyl phthalate,” while also listing multiple synonyms, including “1,2-benzenedicarboxylic acid, dimethyl ester.” You add that both “dimethyl phthalate” and “1,2-benzenedicarboxylic acid, dimethyl ester” are listed in the hazardous substances table in Appendix A to § 172.101 - List of Hazardous Substances and Reportable Quantities with a reportable quantity (RQ) of 5,000 pounds. You ask whether it is permissible to use a synonym or alternate name listed in an SDS as the technical name for a material if the synonym is listed in Appendix A to § 172.101. Additionally, you ask if the synonym is not listed in Appendix A of § 172.101 but is included as another name under the Chemical Abstracts Service (CAS) record, whether it is permissible to use that synonym as the technical name for a hazardous substance in the basic shipping description. As stated in § 172.203(c) of the HMR, the name of the hazardous substance must be entered in parentheses in association with the basic description when the proper shipping name for a material does not identify the hazardous substance by name. Both “dimethyl phthalate” and “1,2-benzenedicarboxylic acid, dimethyl ester” are listed as hazardous substances in Appendix A to § 172.101 and they are synonyms of the same chemical. As such, it is the opinion of this Office that the proper shipping name could appear as either “UN3082, Environmentally hazardous substance, liquid, n.o.s., 9, III (Dimethyl phthalate)” or “UN3082, Environmentally hazardous substance, liquid, n.o.s., 9, III (1,2-Benzenedicarboxylic acid, dimethyl ester).”#

Page 2Lastly, § 172.203(c) requires that the name of the hazardous substance listed in Appendix A to § 172.101 appear as the technical name in the basic shipping description if the proper shipping name for a material that is a hazardous substance does not identify the hazardous substance by name. The HMR does not permit the use of a synonym under a CAS record that is not listed in Appendix A to § 172.101 to describe a hazardous substance on shipping papers. I hope this information is helpful. Please contact us if we can be of further assistance. Sincerely, T. Glenn Foster Chief, Regulatory Review and Reinvention Branch Standards and Rulemaking Division#

Page 3Andrews 23-0008 From: INFOCNTR (PHMSA) To: Hazmat Interps Subject: FW: Interpretation Seeking on Technical Name Synonym Date: Tuesday, January 31, 2023 3:47:53 PM Attachments: image001.png image002.png image003.png image004.png image005.png image006.png image007.png image008.png DMP DGD.pdf DMP SDS.pdf Please see below and attached request for interpretation. Thanks, Jonathon, HMIC From: Le, Hien <Hien.Le@leschaco.com> Sent: Monday, January 30, 2023 5:35 PM To: INFOCNTR (PHMSA) <INFOCNTR.INFOCNTR@dot.gov> Cc: Le, Hien <Hien.Le@leschaco.com> Subject: Interpretation Seeking on Technical Name Synonym CAUTION: This email originated from outside of the Department of Transportation (DOT). Do not click on links or open attachments unless you recognize the sender and know the content is safe. Dear PHMSA, I am writing this email seeking interpretation on 49 CFR 172.203(k). technical name(s) in parenthesis on the shipping documents after PSN with “n.o.s.” This part generally outlines the requirement of listing the In addition, this part directs reader to 49 CFR 171.8 for additional technical name options. This email lays out a specific situation for UN3082. Section 14 of the attached safety data sheet (SDS) states the technical name for this product (DMP) as “Dimethyl Phtalate.” However, in section 1 of the same SDS, the manufacturer lists other names under “Synonyms.” Screen shots of section 1 and 14 are as follows. 14. TRANSPORT INFORMATION Description of waste residues and information on their safe handling and methods of disposal: UN number 3082 UN roper shi ping name Environmentally hazardous substances, liquid, n.o.s. (Dimethyl phthalate 1. IDENTIFICATION OF SUBSTANCE/ MIXTURE AND OF SUPPLIER Product Identifier: High Purity Chemicals Synonyms: 1,2-Benzenedicarboxylic Acid, Dimethyl Ester; D.M.P. ; Phthalic Acid, Dimethyl Ester; dimethyl benzeneorthodicarboxylate; Methyl Phthalate Other means of identification: CAS No. 131-11-3 EINECS No. 205-011-6 Recommended use of the chemical and restrictions on use: Commonly used as a plasticizer. The shipper has used one of the synonyms listed in section 1 as technical name for their shipping document (reacted copy attached). Further investigation of technical name definition under 49 CFR 171.8, the regulation asks not to use trade name and if the substance is listed on Appendix A to Part 172.101, then the substance name must be used. In this case, both “Dimethyl phthalate” and “1,2-benzenedicarboxylic acid, dimethyl ester” are listed on Appendix A and have the same RQ limit (5000 lbs). Additional effort to confirm if the two substance texts are the same or not is conducted using the CAS No. 131-11-3. The NIST link (https://webbook.nist.gov/cgi/cbook.cgi?ID=131-11-3) shows both technical name texts under the same CAS no.#

Page 4N•~?NAT!ONALINSTITUTEOF • ~ 1 I srA~~,°;,~o.,re;'"N,?LoGv NIST Chem1stryWebBook1 SRD 69 ft Search..- NISTDataT AboutT Dimethyl phthalate • Formula: C10H10O4 • Molecular weight: 194.1840 • IU PAC Standard lnChl: lnChl =15/C10H1004/cl-13-9(11)7-5-3-4-6-8(7)10(12)14-2/ h3-6H,1-2H3 [[) ~ " E J!I • IUPACStandard lnChlKey: NIQCtJGHVCWTJSM- UHFFFAOYSA- N.0 • CAS Registry Number: 131-11-3 • Chemicalstructure: Th is structure is also available as a 2d Mol fil e or as a computed 3d SD file The 3d structure may be viewe<l using J ava or Java script. • Other na mes: 1,2-Benzenedicarboxylic acid, dimethyl ester; Phthalic acid, dimethyl ester; Avolin; Dimethyl 1,2-benzenedicarboxylate; DM F , Insect repellent; DMP; Fermine; Mipax; NTM; Palatino! M; Sotvanom; Solvarone; Unimoll DM; Dimethy( benzeneorthodicarboxylate; Dimethyl orthophthalate; Dimethyl benzene-o-dicarboxylate; Dimethyl o-phthalate; ENT 262; Phthalsaeuredimethylester; Dimethyl 1,2-benzendicarboxylate; Ke mester DM P; K oda fl ex DM P; Repefta!; Uniplex llO; 1,2-dimethy! phthalate; 1,2-Benzenedicarboxylic acid, 1,2-dimet hyl ester; NSC 1S398; 64441-70-9 The question is posed that if it is legal to use the synonym (or other name) on the SDS as alternative technical name (such as in this case) or not? In addition, if the synonym is not on the Appendix A; however, such name is included as other name under the CAS record, will it be legal to use and bridge the gap using the CAS number? In the latter case, I understand that requirement for RQ or Marine Pollutant is still applicable if other technical name is listed on Appendix A and / or B. Thank you so much in advance, Kind regards, Hien Le, CDGP | he, him, his Manager – Hazmat and Compliance - LESCHACOLeschaco, Inc. | 15355 Vantage Parkway West, Suite 240 | Houston, TX 77032 | U.S.A. phone (1) 281.590 2536 | mobile (1) 346.364.8750 hien.le@leschaco.com www.leschaco.com Twitter LinkedIn WeChat C-TPAT CERTIFIED - Find out the benefits of becoming C-TPAT certified Xing#

Page 5AARTI INDUSTRIES LIMITED MATERIAL SAFETY DATA SHEET Dimethyl Phthalate (DMP) 1. IDENTIFICATION OF SUBSTANCE/ MIXTURE AND OF SUPPLIER Product Identifier: High Purity Chemicals Synonyms: 1,2-Benzenedicarboxylic Acid , Dimethyl Ester; D.M.P.; Phthalic Acid , Dimethyl Ester; dimethyl benzeneorthodicarboxylate; Methyl Phthalate Other means of identification: CAS No. 131-11-3 EINECS No. 205-011-6 Recommended use of the chemical and restrictions on use: Commonly used as a plasticizer. Supplier Details: 71 , Udyog Kshetra, Mulund-Goregaon Link Road, Mulund (West), Mumbai-400080, INDIA. Aarti Industries Limited 71 , Udyog Kshetra , Mulund-Goregaon Link Road , Mulund (West), Mumbai-400080, INDIA. 2. HAZARDS IDENTIFICATION OSHA Hazards: Target organ effect, Teratogen Target Organs: Nerves NFPA Revisim..,~~artiLRi86stfi~Q.com I CIN: Lft'i1_DG;jr198tl~7J.Qfl · . _ INDIA. . . . d Kshetra 2nd Floor Mulund Goregaon Link Road, Mulund (W), Mumbai 400080, Page 1 Agft· Office . 71, U ~0?022-67976666, F : 022-2565 3234 \ E : info@aa_rti-industries.com . Regd. Office: Plot No. 801 , 801123, lllrd Phase, GIDC Vapi-396195, D1st-Valsad. lNDIA. T. 0260-2400366.#

Page 6AARTI INDUSTRIES LIMITED Signal Word: WARNING! Hazard statement(s) H320 H402 Precautionary statement(s) P305 + P351 + P338 Causes eye irritation Harmful to aquatic life. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Seek medical attention. GHS Classification(s) Acute aquatic toxicity (Category 3) Eye irritation (Category 2B) Other hazards which do not result in classification: Potential Health Effects: Organ Description Eyes Ingestion Inhalation Skin Can be irritating to the eyes. Can be harmful if ingested . Can be harmful, causing irritation to the respiratory tract, if inhaled. Product can rapidly absorb through the skin and cause irritation. 3. COMPOSITION AND INFORMATION ON INGREDIENTS Chemical identity: Dimethyl Phthalate Common name I Synonym: 1,2-Benzenedicarboxylic Acid, Dimethyl Ester; D.M.P .; Phthalic Acid, Dimethyl Ester; dimethyl benzeneorthodicarboxylate; Methyl Phthalate CAS number: 131-11-3 EINECS number: 205-011-6 ICSC number: 0261 RTECS#: Tl1575000 UN#: 3082 % Weight Material CAS 90-100 Dimethyl Phthalate 131-11-3 4. FIRST AID MEASURES General advice Take proper precautions to ensure your own health and safety before attempting rescue and providing first aid. ~0STR1~ C ---••mm:aEE==l•~•!i-~~~~~=======:-::::-==~ ~ ~ ~ lJM B-AI ~ =::============== Revis~li'Jrti-intt\l~t,\~~R:om I CIN: L2~0Sil19ENBhffi~DU)__...., § . I Admin. Office : 71, Udyog Kshetra, 2nd Floor, Mulund Goregaon Link Road'. ~ulun . , ..-,u a1 - 400080, INDIA. Page 2 of 9 T : 022~67976666, F : 022-2565 3234 I E : info@aart1 -1ndustnes.com Regd. Office : Plot No. 801, 801 /23, lllrd Phase, GIDC Vapi-396195, Dist- Valsad. INDIA. T : 0260-2400366.#

Page 7AARTI INDUSTRIES LIMITED Consult a physician. Show this safety data sheet to the doctor in attendance. Move out of dangerous area. Skin Inhalation as needed. Eyes Ingestion Wash skin with soap and copious amounts of water. Seek medical attention. Remove person to fresh air. If signs/symptoms continue, get medical attention. Give oxygen or artificial respiration Thoroughly flush the eyes with large amounts of clean low-pressure water for at least 15 minutes, occasionally lifting the upper and lower eyelids. If irritation persists, seek medical attention. DO NOT induce vomiting . If vomiting does occur, have victim lean forward to prevent aspiration. Rinse mouth with water. Seek medical attention. Never give anything by mouth to an unconscious individual. 5. FIRE FIGHTING MEASURES Suitable (and unsuitable) extinguishing media: Use water spray, alcohol-resistant foam , dry chemical or carbon dioxide. Specific hazards arising from the chemical (e.g., nature of any hazardous combustion products): Carbon oxides expected to be the primary hazardous combustion product. Special protective equipment and precautions for firefighters: Wear self-contained breathing apparatus and protective clothing to prevent contact with skin and eyes. Keep unopened containers cool by spraying with water. Flammable Properties Classification OSHA/NFPA Class 111B Combustible Liquid. Flash point 146 °C (295 °F) - closed cup Autoignition temperature 490 °C (915 °F) 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures: Use personal protective equipment. Do not inhale vapors/misUgas/dust. Ensure adequate ventilation. Evacuate personnel to safe areas. Environmental precautions: Revision Dat~: 15d0? ?I1 1 ?Qcom I CIN· L2~00~1~P * www.aa, ,1-m u-sme-s. · . A d i • Office : 71 , Udyog Kshetra, 2nd Floor, Mulund Goregaon Link Road '. ~ulund_ (W), Mumbai - 400080, INDI • Page ~ !JI ~ T : 022-67976666, F : 022-2565 3234 I E : info@aart1 -1 ndustnes.com Regd. Office : Plot No. 801 , 801 /23, lllrd Phase, GIDC Vapi-396195, Dist- Valsad. INDIA. T : 0260-2400366.#

Page 8AARTI INDUSTRIES LIMITED Stop leak. Contain spill if possible and safe to do so. Prevent product from entering drains. Methods and materials for containment and cleaning up: Absorb with an inert dry material and place in an appropriate waste disposal container. Keep disposal containers closed when finished . 7. HANDLING AND STORAGE Precautions for safe handling: Do not get on skin or in eyes. Do not inhale vapor or mist. Take normal fire prevention measures. Conditions for safe storage, including any incompatibilites: Container must be sealed tightly and kept in a dry, well-ventilated space. 8. EXPOSURE CONTROLS I PERSONAL PROTECTION Control parameters, e.g., occupational exposure limit values or biological limit values: Occupational Exposure Limits Component Source Type Value Note Dimethyl Phthalate US (OSHA TWA 5 mg/m3 29 CFR 1910.1000 Table Z-1 Limits for Air Contaminants Appropriate engineering controls: General room or local exhaust ventilation is usually required to meet exposure limit(s). Electrical equipment should be grounded and conform to applicable electrical code. Individual protection measures, such as personal protective equipment: Respiratory protection: Where risk assessment shows air-purifying respirators are appropriate use a full-face respirator with multi-purpose combination (US) or type ABEK (EN 14387) respirator cartridges as a backup to engineering controls. If the respirator is the sole means of protection, use a full-face supplied air respirator. Use respirators and components tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU). Hand protection: Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands. Eye protection: Use chemical safety goggles and/or a full face shield where splashing is possible. Use equipment approved by appropriate government standards, such as NIOSH (US) or EN166 (EU) Maintain eye wash fountain and quick-drench facilities in work area. Skin and body protection: Revis~ lJJ~.§tlri:i.JiriJt?s~com I CIN: L2'f~~MRbC * Admin. Office : 71, Udyog Kshetra, 2nd Floor, Mulund Goregaon ~ink Road'. ~ulun~ (W), ai - 400080, INDIA. Page 4 of 9 T : 022-67976666, F : 022-2565 3234 I E : info@aart1-industnes.com Regd. Office: Plot No. 801, 801/23, lllrd Phase, GIDC Vapi-396195, Dist- Valsad. INDIA. T: 0260-2400366.#

Page 9AARTI INDUSTRIES LIMITED Wear impervious protective clothing, including boots, gloves, lab coat, apron or coveralls, as appropriate, to prevent skin contact. Hygiene measures: of workday. Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance (physical state, color, etc.) Liquid. Colorless, clear. Odor Specific data not available Odor threshold Specific data not available pH Specific data not available Freezing point 2 °C (36 °F) Initial boiling point and boiling range 282 °C (540 °F) Flash point 146 °C (295 °F) - closed cup Evaporation rate Specific data not available Flammability (solid, gas) Specific data not available Upper/ Lower flammability or explosive limits 8.0% (V) / 0.9% (V) Vapor pressure 0.0020 hPa (0.0015 mmHg) at 20.0 °C (68.0 °F) Vapor Density 6.69 Relative Density 1.19 g/ml at 25 °C (77 °F) Solubility(ies) slightly soluble Partition coefficient n-octanol/water(ies) log Pow: 1.5 Auto-ignition temperature 490 °C (915 °F) Decomposition temperature Specific data not available Formula (DIMETHYL PHTHALATE) C10H10O4 Molecular Weight (DIMETHYL PHTHALATE) 194.18 g/mol 10. STABILITY AND REACTIVITY Chemical Stability Stable under recommended storage conditions. Possibility of hazardous reactions No data available Conditions to avoid (e.g., static discharge, shock or No data available vibration) Incompatible materials Acids, oxidizing agents Hazardous decomposition products Carbon oxides are expected to be, under fire conditions, the primary hazardous decomposition products. 11. TOXICOLOGICAL INFORMATION • Dimethyl Phthalate 131-11-3 ReviS~\1Jv21.tni-rRd~itft~iQ;om I CIN: L2~'0CliA81t4PllCOO'Z30fJ . Admin. Office : 71, Udyog Kshetra, 2nd Floor, Mulund Goregaon Link Road'. ~ulund_ (W), Mumbai - 400080, INDIA. Page 5 of 9 T : 022-67976666, F : 022-2565 3234 I E : info@aart1 -1ndustnes.com Regd. Office : Plot No. 801, 801 /23, lllrd Phase, GIDC Vapi-396195, Dist- Valsad. INDIA. T : 0260-2400366.#

Page 10AARTI INDUSTRIES LIMITED Product Summary: Laboratory test results indicate that the product has reproductive and teratogenic effects. No data available for the mutagenic effects of the product. No data available to designate product as an aspiration hazard or to cause specific target organ toxicity through single or repeated exposure. Acute Toxicity: LD50 Dermal) LD50 (Oral Rabbit Rat Irritation: Eyes Rabbit - mild eye irritation Respiratory or Skin Sensitization No data available Skin No data available Reproductive Toxicity Reproductive disorder(s) have been displayed in laboratory animals overexposed to the material. Teratogenicity May cause congenital malformation in the fetus. Carcinogenicity IARC: No component of this product present at levels greater than or equal to 0.1 % is identified as probable or confirmed human carcinogen by IARC. ACGIH : No component of this product present at levels greater than or equal to 0.1 % is identified as a carcinogen or potential carcinogen by ACGIH. NTP: No component of this product present at levels greater than or equal to 0.1 % is identified as a known or anticipated carcinogen by NTP. OSHA: No component of this product present at levels greater than or equal to 0.1 % is identified as a carcinogen or potential carcinogen by OSHA. Other Hazards Organ Description Eyes Ingestion Inhalation Skin May be irritating to the eyes. May be harmful if ingested. May be harmful if inhaled. May be irritating to the respiratory tract. May be harmful if absorbed through skin. May be irritatinq to the skin.#

Page 11AARTI INDUSTRIES LIMITED 12. ECOLOGICAL INFORMATION • Dimethyl Phthalate 131-11-3 Ecotoxicity (aquatic and terrestrial, where available): Acute Fish Toxicity (DIMETHYL PHTHALATE) LC50 / 96 hours Fathead Minnow - 121 mg/L Acute Fish Toxicity (DIMETHYL PHTHALATE) LC50 / 96 hours Bluegill - 50 mg/L Toxicity to Daphnia (DIMETHYL PHTHALATE) EC50 / 48 hours Water flea - 46 mg/L Persistence and degradability: No data available Bioaccumulative potential: Bioaccumulation: Lepomis macrochirus (Bluegill) - 21 d Bioconcentration factor (BCF): 57 Other adverse effects: Product is harmful to aquatic life and can be considered an environmental hazard if improperly handled or through improper disposal. 13. DISPOSAL CONSIDERATIONS Description of waste residues and information on their safe handling and methods of disposal, including the disposal of any contaminated packaging: Observe all federal , state, and local environmental regulations. Contact a licensed professional waste disposal service to dispose of this material. Dissolve or mix the material with a combustible solvent and burn in a chemical incinerator equipped with an afterburner and scrubber. 14. TRANSPORT INFORMATION Description of waste residues and information on their safe handling and methods of disposal: UN number 3082 UN proper shipping name Environmentally hazardous substances, liquid, n.o.s. (Dimethyl phthalate) Transport hazard class es 9 Packin roup if applicable Ill Page 7 of g RevisiWw~~ru1Rt8~~.com I CIN: L~ t00dlll9!il~7J~ * Admin. Office : 71, Udyog Kshetra, 2nd Floor, Mulund Goregaon ~ink Road'. ~ulund_ (W), umbai - T : 022-67976666, F : 022-2565 3234 \ E : info@aart1-1ndustnes.com . Regd. Office : Plot No. S01, 801 /23, lllrd Phase, GIDC Vapi-396195, Dist- Valsad. INDIA. T . 0260-2400366.#

Page 12AARTI INDUSTRIES LIMITED Reportable Quantity 5,000 lbs IMDG UN-Number: Not a dangerous good. Marine pollutant: No IATA UN-Number: Not a dangerous good. 15. REGULATORY INFORMATION Safety, health and environmental regulations specific for the product in question: OSHA Hazards Target organ effect, Teratogen All ingredients are on the following inventories or are exempted from listing Country Notification Australia AICS Canada DSL China IECS European Union EINECS Japan ENCS/ISHL Korea EGL New Zealand NZloC Philippines PIGGS United States of America TSCA SARA 302 Components SARA 302: No chemicals in this material are subject to the reporting requirements of SARA Title Ill, Section 302. SARA 313 Components The following components are subject to reporting levels established by SARA Title 111, Section 313: DIMETHYL PHTHALA TE GAS-No. 131-11-3 Revision Date 2007-07-01 SARA 311/312 Hazards Chronic Health Hazard CERCLA Dimethyl phthalate GAS-No. 131-11-3, RQ: 5,000 lbs Massachusetts Right To Know Components Dimethyl phthalate CAS-No. 131-11 -3 Revision Date 2007-07-01 Page 8 of 9 Revisi&Q,5Ji\ftilt?n!i\1st/r~com I CIN: L:iRcttbaO te!Mffh608:73(U . IA Admin. Office : 71, Udyog Kshetra, 2nd Floor, Mulund Goregaon ~ink Road: Mulun~ (W), Mumbai - 400080, IND . T : 022-67976666, F : 022-2565 3234 \ E : 1nfo@aartHndustnes.com Regd. Office: Plot No. B01, 801 /23, lllrd Phase, GIDC Vapi-396195, Dist- Valsad. INDIA. T: 0260-2400366.#

Page 13AARTI INDUSTRIES LIMITED Pennsylvania Right To Know Components Dimethyl phthalate CAS-No. 131-11-3 Revision Date 2007-07-01 New Jersey Right To Know Components Dimethyl phthalate CAS-No. 131-11-3 Revision Date 2007-07-01 California Prop 65 Components This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm. 16. OTHER INFORMATION: INCLUDING INFORMATION ON PREPARATION AND REVISION OF THE SOS Disclaimer AARTI INDUSTRIES LIMITED believes that the information on this MSDS was obtained from reliable sources. However, the information is provided without any warranty, expressed or implied, regarding its correctness. Some information presented and conclusions drawn herein are from sources other than direct test data on the substance itself. The conditions or methods of handling, storage, use and disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, AARTI INDUSTRIES LIMITED does not assume responsibility and expressly disclaims liability for loss, damage, or expense arising out of or in any way connected with handling, storage, use, or disposal of this product. If the product is used as a component in another product, this MSDS information may not be applicable. Information is correct to the best of our knowledge at the date of the MSDS publication. Revision Date:. 11. 1 i;; O? ?f.l?ncom I CIN· L~•Mffl81fflb60~:73ru www.aan · nausmes; · b · 400080 INDIA Admin. Office : 71, Udyog Kshetra, 2nd Floor, Mulund Goregaon ~ink Road'. ~ulund_ {W), Mum at - , · Page g of g T : 022_ 67976666, F : 022-2565 3234 I E : 1nfo@aart1-industnes.com Regd. Office: Plot No. 801, 801/23, lllrd Phase, GIDC Vapi-396195, Dist- Valsad. INDIA. T: 0260-2400366.#

Page 14h n h n - X C a g e E d - X C a g e E F i F d i P Click to BUY NOW! o r IMO DANGEROUS GOODS DECLARATION P r- 0 r-,.- ...-- - D t D t w m w w w w c w The form meets the requirements of SOLAS 74 chapter VII ,regulation 5:MARPOL 73/78 Annex III ,regulation 4 and the IMDG o Click to BUY NOW! o r m o c . t e . . r r t e . a c a a r k e t w s o code, General Introduction, Section 9 f c k e f t w r - s o Shipper Reference Number(s) Aarti Industries Limited r a 71 Udyog Kshetra,2nd Floor LBS Marg,Mulund Goregaon Link Road, Mulund (West) Emergency Contact Telephone Number Mumbai-400080 TEL: 201-753-5407 201 Maharashtra,India Phone No: +912267976666 Carrier Fax No : +912225653234 Email : info@aartigroup.com CIN - L24110GJ1984PLC007301 Carriers Booking Number. Consignee Bill Of Ladding No. & Date Name/Status , Company/Organization of Signatory Container Packing Certificate/Vehicle Declaration AARTI INDUSTRIES LIMITED / CONTAINER PACKING DECLARATION MR. AMIT DALVI ~ It is hereby declared that the packing of the container has been Place And Date carried out in accordance with the General Introduction , MUMBAI 15.12.2022 IMDG code , paragraph 5.4.2.1 Signature On Behalf Of The Packer / Ships Name & Voyage No MR. AMIT DALVI ~ Container Number(s) Seal NO. 38728 Port Of Unloading SAVANNAH, USA Qty , Type & kind of packages 1 ISO TANK ONLY DI METHYL PHTHALATE (DMP) PO NO GW/TW/NW LOT NO ISO TANK NO: Port Of Loading MUNDRA, INDIA Final Destination SAVANNAH, USA Description(Proper Shipping I I Gross & Net Weights Name,Class,UN,Packing) CHEMICAL. DIMETHYL PHTHALATE 10, MATERIAL NO. 50374 UN NO.3082,ENVIRONMENTALLY HAZARDOUS NT.WT . 19,500.000 GR.WT . 23,390.000 ON AS IS BASIS SUBSTANCE, LIQUID,N.O.S. (1,2-BENZENEDICARBOXYLIC ACID,DIMETHYL ESTER)9,III, CAS NO. 131-11-3 HTS# A2917.34.0150 UN NO:3082 CLASS EMS:9 PG:III Marine Pollutant: UN NO: 3082 Class: 9 P.G: III P.O NO. DT. SHIPPER'S DECLARATION Name/Status,Company/Organization of Signatory AARTI INDUSTRIES LIMITED It is hereby declared that the contents of this consignment are fully AND Place And Date accurately described above by the proper shipping name(s) , and are respects in proper condition for transport according to applicable international and national government regulations. Signature On Behalf Of The Shipper MR. AMIT DALVI#