Verification of Pipeline Material Properties and Attributes: Onshore Steel Transmission Pipelines. [49 CFR 192.607]

(A)A. Applicability. Wherever required by this part, operators of onshore steel transmission pipelines must document and verify material properties and attributes in accordance with this Section. [49 CFR 192.607(a)]#

(B)B. Documentation of Material Properties and Attributes. Records established under this Section documenting physical pipeline characteristics and attributes, including diameter, wall thickness, seam type, and grade (e.g., yield strength, ultimate tensile strength, or pressure rating for valves and flanges, etc.), must be maintained for the life of the pipeline and be traceable, verifiable, and complete. Charpy v-notch toughness values established under this Section needed to meet the requirements of the ECA method at §2724.C.3 or the fracture mechanics requirements at §2912 must be maintained for the life of the pipeline. [49 CFR 192.607(b)]#

(C)C. Verification of Material Properties and Attributes. If an operator does not have traceable, verifiable, and complete records required by Subsection B of this Section, the operator must develop and implement procedures for conducting nondestructive or destructive tests, examinations, and assessments in order to verify the material properties of aboveground line pipe and components, and of buried line pipe and components when excavations occur at the following opportunities: Anomaly direct examinations, in situ evaluations, repairs, remediations, maintenance, and excavations that are associated with replacements or relocations of pipeline segments that are removed from service. The procedures must also provide for the following. [49 CFR 192.607(c)]#

(1)1. For nondestructive tests, at each test location, material properties for minimum yield strength and ultimate tensile strength must be determined at a minimum of 5 places in at least 2 circumferential quadrants of the pipe for a minimum total of 10 test readings at each pipe cylinder location. [49 CFR 192.607(c)(1)]#

(2)2. For destructive tests, at each test location, a set of material properties tests for minimum yield strength and ultimate tensile strength must be conducted on each test pipe cylinder removed from each location, in accordance with API Specification 5L. [49 CFR 192.607(c)(2)]#

(3)3. Tests, examinations, and assessments must be appropriate for verifying the necessary material properties and attributes. [49 CFR 192.607(c)(3)]#

(4)4. If toughness properties are not documented, the procedures must include accepted industry methods for verifying pipe material toughness. [49 CFR 192.607(c)(4)]#

(5)5. Verification of material properties and attributes for non-line pipe components must comply with Subsection F of this Section. [49 CFR 192.607(c)(5)]#

(D)D. Special requirements for nondestructive Methods. Procedures developed in accordance with Subsection C of this Section for verification of material properties and attributes using nondestructive methods must: [49 CFR 192.607(d)]#

(1)1. use methods, tools, procedures, and techniques that have been validated by a subject matter expert based on comparison with destructive test results on material of comparable grade and vintage; [49 CFR 192.607(d)(1)]#

(2)2. conservatively account for measurement inaccuracy and uncertainty using reliable engineering tests and analyses; and [49 CFR 192.607(d)(2)]#

(3)3. use test equipment that has been properly calibrated for comparable test materials prior to usage. [49 CFR 192.607(d)(3)]#

(E)E. Sampling Multiple Segments of Pipe. To verify material properties and attributes for a population of multiple, comparable segments of pipe without traceable, verifiable, and complete records, an operator may use a sampling program in accordance with the following requirements. [49 CFR 192.607(e)]#

(1)1. The operator must define separate populations of similar segments of pipe for each combination of the following material properties and attributes: nominal wall thicknesses, grade, manufacturing process, pipe manufacturing dates, and construction dates. If the dates between the manufacture or construction of the pipeline segments exceeds two years, those segments cannot be considered as the same vintage for the purpose of defining a population under this Section. The total population mileage is the cumulative mileage of pipeline segments in the population. The pipeline segments need not be continuous. [49 CFR 192.607(e)(1)]#

(2)2. For each population defined according to Paragraph E.1 of this Section, the operator must determine material properties at all excavations that expose the pipe associated with anomaly direct examinations, in situ evaluations, repairs, remediations, or maintenance, except for pipeline segments exposed during excavation activities pursuant to §2714, until completion of the lesser of the following: [49 CFR 192.607(e)(2)]#

(a)a. one excavation per mile rounded up to the nearest whole number; or [49 CFR 192.607(e)(2)(i)]#

(b)b. 150 excavations if the population is more than 150 miles. [49 CFR 192.607(e)(2)(ii)]#

(3)3. Prior tests conducted for a single excavation according to the requirements of Subsection C of this Section may be counted as one sample under the sampling requirements of this Subsection E. [49 CFR 192.607(e)(3)]#

(4)4. If the test results identify line pipe with properties that are not consistent with available information or existing expectations or assumed properties used for operations and maintenance in the past, the operator must establish an expanded sampling program. The expanded sampling program must use valid statistical bases designed to achieve at least a 95 percent confidence level that material properties used in the operation and maintenance of the pipeline are valid. The approach must address how the sampling plan will be expanded to address findings that reveal material properties that are not consistent with all available information or existing expectations or assumed material properties used for pipeline operations and maintenance in the past. Operators must notify PHMSA in advance of using an expanded sampling approach in accordance with §518. [49 CFR 192.607(e)(4)]#

(5)5. An operator may use an alternative statistical sampling approach that differs from the requirements specified in Paragraph E.2 of this Section. The alternative sampling program must use valid statistical bases designed to achieve at least a 95 percent confidence level that material properties used in the operation and maintenance of the pipeline are valid. The approach must address how the sampling plan will be expanded to address findings that reveal material properties that are not consistent with all available information or existing expectations or assumed material properties used for pipeline operations and maintenance in the past. Operators must notify PHMSA in advance of using an alternative sampling approach in accordance with §518. [49 CFR 192.607(e)(5)]#

(F)F. Components. For mainline pipeline components other than line pipe, an operator must develop and implement procedures in accordance with Subsection C of this Section for establishing and documenting the ANSI rating or pressure rating [in accordance with ASME/ANSI B16.5 (incorporated by reference, see §507)] . [49 CFR 192.607(f)]#

(1)1. Operators are not required to test for the chemical and mechanical properties of components in compressor stations, meter stations, regulator stations, separators, river crossing headers, mainline valve assemblies, valve operator piping, or cross-connections with isolation valves from the mainline pipeline. [49 CFR 192.607(f)(1)]#

(2)2. Verification of material properties is required for non-line pipe components, including valves, flanges, fittings, fabricated assemblies, and other pressure retaining components and appurtenances that are: [49 CFR 192.607(f)(2)]#

(a)a. larger than 2 inches in nominal outside diameter, [49 CFR 192.607(f)(2)(i)]#

(b)b. material grades of 42,000 psi (Grade X - 42) or greater, or [49 CFR 192.607(f)(2)(ii)]#

(c)c. appurtenances of any size that are directly installed on the pipeline and cannot be isolated from mainline pipeline pressures. [49 CFR 192.607(f)(2)(iii)]#

(3)3. Procedures for establishing material properties of non-line pipe components must be based on the documented manufacturing specification for the components. If specifications are not known, usage of manufacturer's stamped, marked, or tagged material pressure ratings and material type may be used to establish pressure rating. Operators must document the method used to determine the pressure rating and the findings of that determination. [49 CFR 192.607(f)(3)]#

(G)G. Uprating. The material properties determined from the destructive or nondestructive tests required by this Section cannot be used to raise the grade or specification of the material, unless the original grade or specification is unknown and MAOP is based on an assumed yield strength of 24,000 psi in accordance with §907.B.2. [49 CFR 192.607(g)]#

AUTHORITY NOTE: Promulgated in accordance with R.S. 30:501 et seq.#

HISTORICAL NOTE: Promulgated by the Department of Natural Resources, Office of Conservation, LR 46:1588 (November 2020).#